#!/bin/busybox sh
# Stage-2 init: PID 1 on the disk rootfs (rootfs_a or rootfs_b), reached via
# switch_root from the initramfs. Brings up the minimum a WardenOS userspace
# needs — mounts, by-name symlinks, network, serial alias — then starts any
# payload daemons and holds. This stands in for the device's BusyBox SysV
# /etc/init.d/S* sequence; it is deliberately tiny, not a model of it.

/bin/busybox mount -t devtmpfs devtmpfs /dev 2>/dev/null
exec </dev/console >/dev/console 2>&1
/bin/busybox --install -s /bin

mount -t proc proc /proc
mount -t sysfs sysfs /sys
mount -t tmpfs tmpfs /tmp

# Fresh devtmpfs — repopulate the by-name contract (slotctl.rs depends on it).
mkdir -p /dev/block/by-name
for uev in /sys/class/block/vda*/uevent; do
    [ -f "$uev" ] || continue
    partname=""
    devname=""
    while IFS='=' read -r k v; do
        case "$k" in
            PARTNAME) partname="$v" ;;
            DEVNAME)  devname="$v" ;;
        esac
    done < "$uev"
    [ -n "$partname" ] && [ -n "$devname" ] \
        && ln -sf "/dev/$devname" "/dev/block/by-name/$partname"
done

# Slot (whole-token parse, same rule as stage 1).
slot="_a"
for tok in $(cat /proc/cmdline); do
    case "$tok" in
        warden.slot=*) slot="${tok#warden.slot=}" ;;
    esac
done

# The device's matched mounts: persistent state and the slot's oem partition.
mount -t ext4 /dev/block/by-name/userdata /userdata || echo "init: userdata mount failed"
mount -t ext4 "/dev/block/by-name/oem${slot}" /oem || echo "init: oem${slot} mount failed"
mkdir -p /userdata/warden

# RS485: warden-modbus hardcodes /dev/ttyS4 at compile time; alias it to the
# VM's pci-serial UART when one is present (needs the virt.fragment kernel).
[ -c /dev/ttyS0 ] && ln -sf /dev/ttyS0 /dev/ttyS4

# Network: slirp user-mode net on eth0 (DHCP, fallback to QEMU's static map).
ip link set lo up
if [ -e /sys/class/net/eth0 ]; then
    ip link set eth0 up
    if ! udhcpc -i eth0 -n -q -t 5 -T 2 >/dev/null 2>&1; then
        ip addr add 10.0.2.15/24 dev eth0 2>/dev/null
        ip route replace default via 10.0.2.2 dev eth0
        echo "nameserver 10.0.2.3" > /etc/resolv.conf
    fi
fi

hostname warden-qemu

echo "WARDEN-QEMU-ROOTFS-OK slot=${slot}"

# Payload daemons (dropped into /usr/bin by qemu/mkimage.sh from qemu/payload/).
for d in /usr/bin/warden-flared /usr/bin/warden-modbus; do
    if [ -x "$d" ]; then
        name="$(basename "$d")"
        echo "init: starting $name"
        "$d" > "/tmp/${name}.log" 2>&1 &
    fi
done

if grep -qw warden.shell /proc/cmdline; then
    echo "warden.shell: interactive shell (exit powers off)"
    setsid cttyhack sh
    poweroff -f
fi

# Hold: daemons run, console idles, scenarios drive the VM from outside.
while :; do sleep 3600; done
