Preparing the repo to go public (ADR-0007):
- CI: kernel-build moves from the self-hosted runner to ubuntu-latest
(installs its own cross toolchain + qemu, caches the pristine tarball).
On a public repo a registered self-hosted runner is reachable from
approved fork-PR workflows — i.e. arbitrary code on private
infrastructure — and the build never actually needed the SDK host.
ADR-0004 marked superseded-in-part; docs/ci-cd.md rewritten (site
specifics now live only in the private deployment log).
- Licensing: LICENSE gains the GPL-2.0 carve-out for patches/ and the
kernel source excerpts (Linux derivatives; per-driver provenance was
already tracked in PROVENANCE.md); patches/README.md states it too.
- Scrubbed from the tip: bench-unit dev credentials and its gadget IP
(m2-boot notes), the site AP SSID+BSSID and a neighboring AP's BSSID
and the device WLAN MAC (wifi bring-up evidence — BSSIDs are
geolocatable), the runner mesh IP. NOTE: these remain in git history;
decision on a pre-publication history rewrite is separate.
- Emoji cleanup across 21 tracked files (kernel port docs, review report,
enforce-mcdc.sh) per repo text conventions: status marks became
[x]/[wip]/[ ]/OK plain text.
- "[maintainer]-gated" process phrasing normalized to "maintainer-gated"
(attributions in dated evidence docs kept).
Verified: zero emojis tracked; scrub grep clean; patches carry no internal
references; ci.yml parses; shellcheck unchanged.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_018HUayid7W5w7jBdb9Rrj1K
The saradc -22 was regulator_get_voltage on a dummy vref (no vref-supply in
DT), not the clk divider. Added vcc_1v8 fixed 1.8V regulator + vref-supply
(matching the vendor 86-panel). iio:device0 now reads both channels
(in_voltage0_raw=1023, in_voltage1_raw=246) — the adc-keys path works.
Five drivers verified this run: wifi, TRNG, OTP, GMAC, SARADC.
adc/SARADC-FIX.md; DRIVER-PARITY updated.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017wB8KB3MMQztRDXCMCkPrf
usb2phy: ported the RV1106 inno-usb2 phy config to 6.18 (rv1106_usb2phy_cfg;
fields map 1:1 except utmi_iddig->utmi_id and chg_mode->opmode; 5.10-only
iddig_output/en/bvalid_grf_sel dropped; phy_tuning left off, guarded so safe).
With PHY_ROCKCHIP_INNO_USB2=y + the u2phy/usbdrd/dwc3 DT enabled, verified on
warden-c8a3: the DWC3 comes up as xhci-hcd @ 0xffb00000 — USB host works. eth0
gadget just needs dr_mode=peripheral.
saradc: added rv1106_saradc_data (2-ch v2, matches the vendor) + the native
compatible. Driver now matches; probe still returns -22 (a clk-rate/setup detail,
not the data) — TODO.
Also captured: the growing board dts (USB nodes), the port fragments under usb/
and adc/. DRIVER-PARITY.md updated: ~14 drivers now at parity on 6.18.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017wB8KB3MMQztRDXCMCkPrf
