Files
bfe-core1106-sdk/kernel/rv1106-enablement/DRIVER-PARITY.md
T
BFE EngineeringandClaude Opus 4.8 54f961c6b6 kernel/rv1106: PVTM VERIFIED — both monitors probe + read (7th driver)
Whole-driver port (mainline has no rockchip pvtm): copied vendor rockchip_pvtm.c
+ pvtm.h. 6.18 deltas: thermal_zone opaque -> thermal_zone_get_temp; of_device.h.
Real blocker: vendor of_match_table wrapped rv1106 entries in #ifdef
CONFIG_CPU_RV1106 (nonexistent in mainline) -> devices+driver present but never
bound, probe silent. Dropped the guard -> both bind.

Verified: ff240000.pvtm + ff390000.pvtm probed; /sys/kernel/debug/pvtm/{core,pmu}/
value read ring-osc counts (71682 90462 / 35772). pvtm/PORT-DONE.md.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017wB8KB3MMQztRDXCMCkPrf
2026-08-25 07:25:49 -06:00

49 lines
3.8 KiB
Markdown
Raw Blame History

This file contains ambiguous Unicode characters
This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.
# RV1106 6.18 driver parity vs the 5.10 vendor kernel
Goal: every driver the panel's 5.10 kernel runs must work at ≥ parity on our
self-built 6.18. Source of truth = the running 5.10 system on warden-c8a3
(`lsmod` + `/proc/interrupts`, captured 2026-08-24). Verify each on hardware via
the A/B `_b`-slot loop (`../docs/m2-boot-on-c8a3.md`); ✅ means confirmed on
c8a3, not just compiled.
| Driver / node | 5.10 evidence | mainline? | 6.18 status |
|---|---|---|---|
| CRU clock (clk-rv1106) | — | ported | ✅ M2 |
| pinctrl-rockchip (rv1106) | — | ported | ✅ M2 |
| GIC-400 / arch_timer | arch_timer | mainline | ✅ M2 |
| dw_mmc (eMMC) | dw-mci | mainline | ✅ M3 |
| 8250 uart2 (console) | ttyS2 | mainline | ✅ M2 |
| GPIO (rockchip, ×5 banks) | gpio-rockchip | mainline | ✅ batch1 (chips 04) |
| DMA (pl330, ff420000) | ff420000.dma-controller | mainline | ✅ batch1 |
| uart1 / uart4 | ttyS1, ttyS4 | mainline | ✅ batch1 |
| I2C (dw-apb, ff460000=i2c3) | ff460000.i2c | mainline | ✅ batch1 (i2c-3) |
| watchdog (dw-wdt, ff5a0000) | ff5a0000.watchdog | mainline | ✅ batch1 (watchdog0) |
| tsadc thermal (ff3c8000) | rockchip_thermal | ported (data+init+macros) | ✅ soc-thermal reads 39.8°C |
| SARADC (ff3c0000) | ff3c0000.saradc | ported (2-ch v2 data) | ✅ iio:device0 reads 2ch (adc-keys); fixed -22 via vref-supply |
| TRNG (rng@ff448000) | rockchip,trngv1 | mainline (rk3588 IP) | ✅ /dev/hwrng, real entropy (`rng-otp/`) |
| OTP/nvmem (ff3d0000) | rockchip,rv1106-otp | ported (px30_otp_read) | ✅ rockchip-otp0, reads chip id |
| GMAC (ffa80000) | rockchip,rv1106-gmac | ported (dwmac-rk rv1106_ops) | ✅ eth0 Link Up 100M/Full (`gmac/`) |
| GPIO_SYSFS (legacy /sys/class/gpio) | — | mainline (config) | ⬜ goodix script needs it |
| PWM (rockchip) | — | mainline (=m) | ⬜ batch2 =y (backlight) |
| RTC (rv1106-rtc) | — | ported (vendor driver) | ✅ /dev/rtc0 registers + reads |
| USB2 phy (inno, rv1106) | rockchip_usb2phy_* | ported (data, no tuning) | ✅ probes → USB up |
| USB host (DWC3→xhci, ffb00000) | xhci-hcd:usb1 | mainline | ✅ xhci host registered |
| USB OTG gadget (DWC3, eth0) | eth0 | mainline dwc3 | 🔨 host works; eth0 needs dr_mode=peripheral |
| crypto (aes/ccm/ctr/arc4) | modules | mainline | ⬜ batch2 (config =y) |
| PSCI node (removed) | — | — | ✅ deleted (no secure monitor → SMC fault) |
| VOP display (ff990000) | ff990000.vop | ported (rv1126 sibling) | 🔨 binds+DRM+card0; connector WIP |
| PWM backlight (pwm1) | — | mainline (rk3328 fallback) | ✅ backlight up (brightness) |
| RGB666 720×720 panel | — | panel-dpi | 🔨 probes; bus_format + connector WIP |
| GT911 touch (goodix) | goodix, gt911 | mainline | ⬜ M4 (needs GPIO_SYSFS ✅ + node) |
| GPIO_SYSFS / crypto / CFG80211 | — | mainline (config) | ✅ =y (batch2) |
| AIC8800 wifi (bsp/fdrv) | aic8800_* | **out-of-tree** | ✅ M5 — wlan0 up, scanned the site AP at 43dBm (modules, `wifi/VERIFIED-on-c8a3.md`) |
| AIC8800 BT (btlpm) | aic8800_btlpm | **out-of-tree** | 🔨 module built (6.18 vermagic); HCI bring-up not yet exercised |
| NPU (rknpu, ff660000) | rknpu, ff660000.npu | **out-of-tree** | ⬜ M6 — plan: `npu/PORT-PLAN.md` |
| RGA 2D (rga2) | rga2 | ported (vendor char-dev) | ✅ /dev/rga, hw 3.3.87975 |
| I2S audio (i2s-tdm) | i2s | rv1126 fallback (=y) | ✅ cpu DAI registers (part of the card below) |
| Audio codec (acodec) | rockchip,rv1106-codec | ported (rv1106_codec.c) | ✅ card `rv1106-acodec`, pcmC0D0p/c (`audio/`); audible test @ bench |
| PVTM (core+pmu ring-osc) | rockchip,rv1106-*-pvtm | ported (vendor, no mainline) | ✅ both probe; debugfs reads (`pvtm/`) |
| FIQ debugger (ttyFIQ0) | fiq_glue | rockchip | ⬜ optional (we use ttyS2) |
Legend: ✅ verified on hardware · 🔨 built, not yet verified · ⬜ not started.