bfe-core1106-sdk/kernel/rv1106-enablement/dts/rv1106-warden-m2.dts

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Minimal RV1106 devicetree for the WardenOS 86-Panel — M2 "earlycon" bring-up
 * of the self-built Linux 6.18 forward-port (warden-sdk kernel/docs/bringup.md).
 *
 * Deliberately NOT the full vendor rv1106.dtsi: just the core needed to reach
 * "it's alive" on the debug UART — CPU, GIC, arch timer, RAM, the CRU (our
 * ported clk-rv1106), GRF, and uart2 (the console, driven by mainline 8250_dw).
 * earlycon writes uart2's MMIO directly at the bootloader's divisor, so it prints
 * before the clock/pinctrl drivers probe; the real ttyS console then needs the
 * CRU to hand out SCLK_UART2, which is exactly what this validates on hardware.
 *
 * PORT-VERIFY (must be checked against the TRM / on hardware before trusting a
 * boot — a wrong value here silently hangs the board):
 *   - memory size/base (256 MiB @ 0x0 assumed for the 86-Panel; the loader
 *     usually patches this — confirm against the real DDR init);
 *   - uart2 is the console at 0xff4c0000 (matches the vendor ttyFIQ0 base);
 *   - CRU needs no assigned-clocks here (PLLs keep their loader rates) — fine for
 *     earlycon/console, revisit for the full clock tree.
 */
/dts-v1/;

#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/rv1106-cru.h>

/ {
	model = "WardenOS 86-Panel (RV1106) — M2 earlycon bring-up";
	compatible = "rockchip,rv1106";
	#address-cells = <1>;
	#size-cells = <1>;
	interrupt-parent = <&gic>;

	aliases {
		serial2 = &uart2;
	};

	chosen {
		stdout-path = "serial2:115200n8";
		/*
		 * earlycon with no baud = reuse the divisor the bootloader left in
		 * uart2, so the first prints work regardless of our clock tree. The
		 * ttyS console rate (1.5M) is PORT-VERIFY against the board.
		 */
		bootargs = "earlycon=uart8250,mmio32,0xff4c0000 console=ttyS2,115200n8 earlyprintk rootwait";
	};

	memory@0 {
		device_type = "memory";
		reg = <0x00000000 0x10000000>; /* 256 MiB — PORT-VERIFY */
	};

	xin24m: oscillator {
		compatible = "fixed-clock";
		clock-frequency = <24000000>;
		clock-output-names = "xin24m";
		#clock-cells = <0>;
	};

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		cpu0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-a7";
			reg = <0x0>;
			clocks = <&cru ARMCLK>;
		};
	};

	timer {
		compatible = "arm,armv7-timer";
		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>,
			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
		clock-frequency = <24000000>;
	};

	gic: interrupt-controller@ff1f0000 {
		compatible = "arm,gic-400";
		interrupt-controller;
		#interrupt-cells = <3>;
		#address-cells = <0>;
		reg = <0xff1f1000 0x1000>,
		      <0xff1f2000 0x2000>,
		      <0xff1f4000 0x2000>,
		      <0xff1f6000 0x2000>;
		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
	};

	grf: syscon@ff000000 {
		compatible = "rockchip,rv1106-grf", "syscon", "simple-mfd";
		reg = <0xff000000 0x68000>;

		/* The CRU's clk-rv1106 registers a second branch set against this
		 * GRF clock-controller (grf_ctx); without the node grf_ctx is NULL
		 * and of_clk_init NULL-derefs in rockchip_clk_register_branches. */
		grf_cru: grf-clock-controller {
			compatible = "rockchip,rv1106-grf-cru";
			#clock-cells = <1>;
		};
	};

	cru: clock-controller@ff3a0000 {
		compatible = "rockchip,rv1106-cru";
		reg = <0xff3a0000 0x20000>;
		rockchip,grf = <&grf>;
		clocks = <&xin24m>;
		clock-names = "xin24m";
		#clock-cells = <1>;
		#reset-cells = <1>;
	};

	uart2: serial@ff4c0000 {
		compatible = "rockchip,rv1106-uart", "snps,dw-apb-uart";
		reg = <0xff4c0000 0x100>;
		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
		reg-shift = <2>;
		reg-io-width = <4>;
		clock-frequency = <24000000>;
		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
		clock-names = "baudclk", "apb_pclk";
		status = "okay";
	};

	/* M3: the eMMC (dw_mmc). Lets the kernel enumerate mmcblk0 and mount an
	 * ext4 rootfs. ciu-drive/ciu-sample clocks come from grf_cru, so the
	 * grf-clock-controller node above is a hard dependency. */
	emmc: mmc@ffa90000 {
		compatible = "rockchip,rv1106-dw-mshc", "rockchip,rk3288-dw-mshc";
		reg = <0xffa90000 0x4000>;
		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru HCLK_EMMC>, <&cru CCLK_SRC_EMMC>,
			 <&grf_cru SCLK_EMMC_DRV>, <&grf_cru SCLK_EMMC_SAMPLE>;
		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
		fifo-depth = <0x100>;
		max-frequency = <200000000>;
		rockchip,use-v2-tuning;
		bus-width = <8>;
		non-removable;
		cap-mmc-highspeed;
		mmc-hs200-1_8v;
		status = "okay";
	};
};